MF Transmitter
PH/TDS/DO/TURBIDITY
WMF2000
Features
- Zero potential point: 7 ± 0.5 pH
- Conversion coefficient: > 96%
- Installation size: 3/4NPT
- Pressure: 1 ~ 6 Bar at 25 ℃
- Temperature: 0 ~ 60℃ for general cables
A general-purpose controller for water quality is a digital analyzer monitor. It may be used with the digital sensors from Wellkonix various water quality series. It is used to track several aspects of water quality, such as conductivity, dissolved oxygen, pH, ORP, turbidity, and concentration of sludge. For record-keeping purposes, the parameters are transmitted by current transmission or RS485 to the monitoring room.
01
Introduction of MF Transmitter
A general-purpose controller for water quality is a digital analyzer monitor. It may be used with the digital sensors from wellkonix's various water quality series. It is used to track several aspects of water quality, such as conductivity, dissolved oxygen, pH, ORP, turbidity, and concentration of sludge.A digital analyzer monitor is an electronic device used to measure, display, and analyze various parameters such as voltage, current, temperature, or frequency. It converts analog signals into digital data, providing real-time monitoring with high accuracy. These monitors are widely used in industrial, laboratory, and healthcare settings to ensure precision in measurements and facilitate data logging and analysis. Key features often include multiple input channels, data storage, and connectivity options for integration with other systems.Industrial: Used for monitoring machinery, processes, and electrical systems to ensure operational efficiency and safety. Laboratory: Provides precise measurements for experiments and research. Healthcare: Monitors vital signs and other physiological parameters in medical devices.
02
Applications of MF Transmitter
separating the output while causing little interference. cutting off RS485 connectivity. temperature measurement, EC/TDS measurement, RS485 communication, sending output, top/bottom limit control. Both an auto and manual temperature offset feature is programmable. Upper/lower limit warning and delay that may be configured. LCD backlight switch and hummer with adjustable settings. addition of a passcode that works everywhere.
03
Uses of MF Transmitter
Process Control: Monitors variables like temperature, pressure, and flow in manufacturing processes to ensure optimal performance and safety. Machine Monitoring: Tracks the health of industrial machinery by measuring vibration, electrical parameters, and other critical indicators to predict and prevent failures. Power Systems: Used to monitor electrical parameters like voltage, current, and power quality in power generation and distribution systems.
MF Transmitter Calibration
Calibrating a digital analyzer monitor is essential to maintain accuracy in measuring various parameters such as voltage, current, temperature, or other signals. The process begins by gathering the required calibration equipment, including known reference standards or signals, calibration software (if applicable), and any specific tools recommended by the manufacturer. Start by powering on the digital analyzer monitor and allowing it to warm up to stabilize its readings. Connect the monitor to the reference standards, which provide precise known values for the parameters you are calibrating. The monitor’s display or output is then compared to these reference values. Adjust the monitor’s settings, typically through calibration controls or software, to align the measured values with the reference standards.
Technical Specification
Product
MF Transmitter PH/TDS/DO/TURBIDITY
Model
WMF2000
Size
96*96mm
Basic Error Of Electronic Unit
pH: (0-14) pH
ORP: (-2000-2000) mV
DO: (0-40) mg/L
TDS: (0-600) mS/cm
Turbidity: (0-4000) NTU
Suspended solids: (0-120000) mg/L
Relative humidity
(10~85)%
Temperature range
(0 ~ 60)℃
Communication
RS485, Modbus-RTU
Transmission signals
4-20mA, maximum loop 500Ω, 0.2%FS
Power supply
220-230VDC±10%
Relay output
250VAC, 3A
Measure Range
PH(0-14) / ORP(-1000~+1000mV)
Temperature compensation
NTCS10K (Standard) & PT1000
Sensors
Features
Direct change over to
Conducvity (µScm )
TDS measurement (ppm )
Automac temperature compensaon
4-20 mA Isolated Output
Large LCD display with background lighng
IP54 water resistant and corrosion proof
enclosure
Using the setup program: user-friendly
programming
RS485 communicaon
Relay output
Affordable
Ease of operaon
Low maintenance
Ensures product quality
A tool for determining a solution’s electrical conductivity is a conductivity sensor. It is often utilized in many different sectors, including water treatment, food & beverage, and medicines. The sensor measures a solution’s capacity to carry an electrical current. To do this, submerge two electrodes in the fluid and briefly apply voltage between them.
The concentration of dissolved ions in a solution is directly correlated with its conductivity. As a result, the sensor may be used to measure the concentration of several ions, including calcium, sodium, and chloride. Numerous variables, like the solution’s purity and temperature, affect the sensor’s accuracy.
Applications
Heating and Cooling Reactors
Disinfecting and
Sterilizing
Waste Heat Recovery Boilers
Dyeing WasteWater
Exhaust Gas Treatment
content.
Fertigation System
Accessories
Documents
Wellkonix global commitment to the Chemical Industry
Wellkonix is the world leader in automation solutions to the chemical industry. As a global player, we have strong local support in any region that you run your business
Providing solutions of every kind, at all times in chemical industries
Wellkonix engineers were all very affected person and cooperative during the early engineering and start-up phases. We labored as one team thru to the completion of this plant project